Radiatoripermotoriは実際の環境で本格的なCiscoの350-401学習範囲「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」の試験の準備過程を提供しています。もしあなたは初心者若しくは専門的な技能を高めたかったら、RadiatoripermotoriのCiscoの350-401学習範囲「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」の試験問題があなたが一歩一歩自分の念願に近くために助けを差し上げます。試験問題と解答に関する質問があるなら、当社は直後に解決方法を差し上げます。 RadiatoripermotoriのCiscoの350-401学習範囲問題集を買う前に、一部の問題と解答を無料に試用することができます。そうすると、RadiatoripermotoriのCiscoの350-401学習範囲トレーニング資料の品質をよく知っています。 我々は心からあなたが首尾よく試験に合格することを願っています。

CCNP Enterprise 350-401 Radiatoripermotoriには専門的なエリート団体があります。

Ciscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)学習範囲認定試験は実は技術専門家を認証する試験です。 関連する研究資料によって、Ciscoの350-401 試験合格攻略認定試験は非常に難しいです。でも、心配することはないですよ。

でも、成功へのショートカットがを見つけました。RadiatoripermotoriのCiscoの350-401学習範囲試験トレーニング資料を利用して気楽に試験に合格しました。それはコストパフォーマンスが非常に高い資料ですから、もしあなたも私と同じIT夢を持っていたら、RadiatoripermotoriのCiscoの350-401学習範囲試験トレーニング資料を利用してください。

Cisco 350-401学習範囲 - 勉強があなたに無敵な位置に立たせます。

あなたの夢は何ですか。あなたのキャリアでいくつかの輝かしい業績を行うことを望まないのですか。きっと望んでいるでしょう。では、常に自分自身をアップグレードする必要があります。IT業種で仕事しているあなたは、夢を達成するためにどんな方法を利用するつもりですか。実際には、IT認定試験を受験して認証資格を取るのは一つの良い方法です。最近、Ciscoの350-401学習範囲試験は非常に人気のある認定試験です。あなたもこの試験の認定資格を取得したいのですか。さて、はやく試験を申し込みましょう。Radiatoripermotoriはあなたを助けることができますから、心配する必要がないですよ。

Radiatoripermotoriのトレーニング資料は１００パーセントの合格率を保証しますから、あなたのニーズを満たすことができます。空想は人間が素晴らしいアイデアをたくさん思い付くことができますが、行動しなければ何の役に立たないのです。

350-401 PDF DEMO:

QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 2
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 3
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

QUESTION NO: 4
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 5
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

SAP C-WME-2506 - あなたは試験の最新バージョンを提供することを要求することもできます。 RadiatoripermotoriのHuawei H20-912_V1.0問題集を利用することです。 Fortinet FCP_FML_AD-7.4認定試験の資格を取得するのは容易ではないことは、すべてのIT職員がよくわかっています。 ATLASSIAN ACP-120 - この試験を受けた身の回りの人がきっと多くいるでしょう。 君がCiscoのVMware 250-599問題集を購入したら、私たちは一年間で無料更新サービスを提供することができます。

Updated: May 28, 2022