現在IT技術会社に通勤しているあなたは、Ciscoの350-401トレーニング資料試験認定を取得しましたか？350-401トレーニング資料試験認定は給料の増加とジョブのプロモーションに役立ちます。短時間で350-401トレーニング資料試験に一発合格したいなら、我々社のCiscoの350-401トレーニング資料資料を参考しましょう。また、350-401トレーニング資料問題集に疑問があると、メールで問い合わせてください。 弊社の無料デモをダウンロードしてあなたはもっと真実に体験することができます。我々は弊社の商品を選ぶお客様に責任を持っています。 だから、我々社は力の限りで弊社のCisco　350-401トレーニング資料試験資料を改善し、改革の変更に応じて更新します。

CCNP Enterprise 350-401 だれでも成功したいのです。

あなたは350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)トレーニング資料試験に不安を持っていますか？350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)トレーニング資料参考資料をご覧下さい。 あなたのすべての需要を満たすためには、一緒に努力します。躊躇われずに我々の模試験を利用してみてください。

Radiatoripermotoriはきみの貴重な時間を節約するだけでなく、 安心で順調に試験に合格するのを保証します。Radiatoripermotoriは専門のIT業界での評判が高くて、あなたがインターネットでRadiatoripermotoriの部分のCisco 350-401トレーニング資料「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」資料を無料でダウンロードして、弊社の正確率を確認してください。弊社の商品が好きなのは弊社のたのしいです。

Cisco 350-401トレーニング資料 - Radiatoripermotoriには専門的なエリート団体があります。

もしあなたはまだCiscoの350-401トレーニング資料試験に合格するのために悩まればRadiatoripermotoriは今あなたを助けることができます。Radiatoripermotoriは高品質の学習資料をあなたを助けて優秀なCiscoの350-401トレーニング資料会員の認証を得て、もしあなたはCisco 350-401トレーニング資料の認証試験を通して自分を高めるの選択を下ろして、Radiatoripermotoriはとてもよい選択だと思います。

試験の目標が変わる限り、あるいは我々の勉強資料が変わる限り、すぐに更新して差し上げます。あなたのニーズをよく知っていていますから、あなたに試験に合格する自信を与えます。

350-401 PDF DEMO:

QUESTION NO: 1
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

QUESTION NO: 2
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 3
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 4
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").

QUESTION NO: 5
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

きみはCiscoのHashiCorp Terraform-Associate-003認定テストに合格するためにたくさんのルートを選択肢があります。 CompTIA DA0-002 - Radiatoripermotoriを選んだら、成功への扉を開きます。 CompTIA CAS-004認定試験は専門知識と情報技術を検査する試験で、Radiatoripermotoriが一日早くCiscoのCompTIA CAS-004認定試験「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」に合格させるのサイトで試験の前に弊社が提供する訓練練習問題をテストして、短い時間であなたの収穫が大きいです。 Cisco 300-435J - Radiatoripermotoriはあなたが試験に合格するのを助けることができるだけでなく、あなたは最新の知識を学ぶのを助けることもできます。 Salesforce Field-Service-Consultant - 試験に合格するのは簡単ではないもよくわかりましょう。

Updated: May 28, 2022